Difference between revisions of "RetroTINK2X"

From Classic Console Upscaler wiki
Jump to navigation Jump to search
(added section on power)
(continued to flesh out page)
Line 34: Line 34:
 
Do not use a power supply rated for AC output, or a power supply rated higher than 5 volts DC, doing so can damage the RetroTINK 2X.  
 
Do not use a power supply rated for AC output, or a power supply rated higher than 5 volts DC, doing so can damage the RetroTINK 2X.  
  
== Inputs ==
+
== AV Inputs ==
  
* [[Composite]]
+
RetroTINK 2X has three AV inputs. The currently selected input can be selected by pressing the input switch, which is the bottom of the two push button switches on the left of the unit. The input signal can be 240/288p or 480/576i (NTSC/PAL).
* [[S-video]]
 
* [[Component]]
 
* [[Analog Audio]]
 
<br>
 
The signal can be 240/288p or 480/576i (NTSC/PAL).
 
(480p input is not compatible on the Component input)
 
  
== Outputs ==
+
'''Important''' - Ensure that only one powered input is connected at any one time. For example, if devices are connected to S-Video and composite inputs at the same time, only the device currently in use can be powered, the other device must be powered off.
  
* [[HDMI]]
+
=== Composite video ===
<br>
+
 
The connector is a miniHDMI that outputs 480p/576p (line-doubled mode)
+
The yellow connector on the front of the unit on the right hand side accepts a standard composite video (CVBS) signal suppled by a single RCA cable. Both PAL and NTSC formats are supported.
or input resolution (pass-thru mode)
+
 
 +
=== S-Video ===
 +
 
 +
A S-Video device outputting a separate luma and chroma signal can be connected to the S-video input using a standard S-video cable. Both PAL and NTSC formats are supported.
 +
 
 +
=== Component video ===
 +
 
 +
A standard YPBPR component video signal can be input using the 3 RCA connectors on the front of the unit. Both PAL and NTSC formats are supported. Only 15khz resolutions are supported, 480p (and higher) resolutions are not supported and will not work.
 +
 
 +
Not that it is '''NOT''' possible to input RGB video using all four RCA connectors at the same time.
 +
 
 +
=== Analog Audio ===
 +
 
 +
Connect a standard stereo analogue audio signal to the two RCA connectors on the right of the unit. This audio will be digitised and output via HDMI with the currently active video input.
 +
 
 +
== Output ==
 +
 
 +
RetroTINK 2X has a single HDMI video output. The connector is a mini HDMI that outputs 480p/576p in line-doubled mode or input resolution in passthrough mode.

Revision as of 16:59, 28 September 2018

RetroTINK-logo.png

RetroTINK Unit

Introduction

RetroTINK 2X is an affordable composite, S-Video, component video and analogue audio to HDMI transcoder/converter designed by Mike Chi.

Rather than being an all-purpose line doubler like the OSSC, RetroTINK 2X aims to be a highly affordable device that can function either as a basic transcoder, line doubler on its own, or as a device integrated into a more complex setup.

Specifications

  • Video inputs: component, S-video and composite
  • Video formats: 240p/480i, 288i/576i, NTSC and PAL color
  • Video sync recovery and regeneration for non-standard sources (e.g., SNES)
  • Output: miniHDMI at 480p/576p (line-doubled mode) or input resolution (pass-thru mode)
  • Audio: 24-bit stereo
  • Power: microUSB
  • Ultra-low latency: less than 5 scanlines (83 microseconds)
  • Optional smoothing filter
  • Plexi-glass enclosure

Availability

Pre-assembled units and accessories will soon be available from VideoGamePerfection.com (EU) and CastleMania Games (US).

More information & discussion

Power

RetroTINK 2X requires an external DC power supply. Since the unit uses a Mini USB connector as a DC power supply input, any powered USB port can be used to supply voltage. If your television has a USB port then this can usually be used to power the device. If you require a separate power supply unit for the device then a suitable power supply can be purchased from VideoGamePerfection.com or from any good electronics retailer.

Do not use a power supply rated for AC output, or a power supply rated higher than 5 volts DC, doing so can damage the RetroTINK 2X.

AV Inputs

RetroTINK 2X has three AV inputs. The currently selected input can be selected by pressing the input switch, which is the bottom of the two push button switches on the left of the unit. The input signal can be 240/288p or 480/576i (NTSC/PAL).

Important - Ensure that only one powered input is connected at any one time. For example, if devices are connected to S-Video and composite inputs at the same time, only the device currently in use can be powered, the other device must be powered off.

Composite video

The yellow connector on the front of the unit on the right hand side accepts a standard composite video (CVBS) signal suppled by a single RCA cable. Both PAL and NTSC formats are supported.

S-Video

A S-Video device outputting a separate luma and chroma signal can be connected to the S-video input using a standard S-video cable. Both PAL and NTSC formats are supported.

Component video

A standard YPBPR component video signal can be input using the 3 RCA connectors on the front of the unit. Both PAL and NTSC formats are supported. Only 15khz resolutions are supported, 480p (and higher) resolutions are not supported and will not work.

Not that it is NOT possible to input RGB video using all four RCA connectors at the same time.

Analog Audio

Connect a standard stereo analogue audio signal to the two RCA connectors on the right of the unit. This audio will be digitised and output via HDMI with the currently active video input.

Output

RetroTINK 2X has a single HDMI video output. The connector is a mini HDMI that outputs 480p/576p in line-doubled mode or input resolution in passthrough mode.