Difference between revisions of "XRGB-2"

From Classic Console Upscaler wiki
Jump to navigation Jump to search
(Menu)
 
(15 intermediate revisions by 2 users not shown)
Line 1: Line 1:
 +
[[File:xrgb-2_front.jpg|300px|thumb|right|XRGB-2 Front]]
 +
[[File:xrgb-2_back.jpg|300px|thumb|right|XRGB-2 Back]]
 +
[[File:Xrgb2box.png|300px|thumb|right|XRGB-2 Box]]
 
The [[XRGB-2]] is an upscan converter by [[Micomsoft]]. It has limited capabilities when compared to the newer units such as the [[XRGB-2 plus]] and the [[XRGB-3]], nevertheless it offers great performance. The stability of the image is rock solid, and you usually don't need to fiddle with settings as much as with later units.
 
The [[XRGB-2]] is an upscan converter by [[Micomsoft]]. It has limited capabilities when compared to the newer units such as the [[XRGB-2 plus]] and the [[XRGB-3]], nevertheless it offers great performance. The stability of the image is rock solid, and you usually don't need to fiddle with settings as much as with later units.
  
It offers no remote control, and all functiosn are available through five buttons on the unit's front.  
+
It offers no remote control, and all functions are available through five buttons on the unit's front. It offers just one scanline setting, equivalent to the 127 setting (50%) on the XRGB-3.
  
 
== Menu ==
 
== Menu ==
Line 17: Line 20:
 
|0 - 62
 
|0 - 62
 
|41
 
|41
|Adjust Brightness
+
|Adjust white level
 
|-
 
|-
 
|
 
|
Line 85: Line 88:
 
|Scanlines
 
|Scanlines
 
|}
 
|}
 +
 +
=== Super Mode menu ===
 +
{| class="wikitable" style="text-align:center; width:40%;"
 +
|-
 +
! scope=col | Menu Heading
 +
! scope=col | Explanation
 +
! scope=col | Allowable Range
 +
! scope=col | Default
 +
|-
 +
|BRIGHTNESS
 +
|Adjust white level
 +
|0 - 62
 +
|41
 +
|-
 +
|BLUE
 +
|Adjust blue
 +
|0 - 62
 +
|31
 +
|-
 +
|GREEN
 +
|Adjust green
 +
|0 - 62
 +
|31
 +
|-
 +
|H_POS
 +
|Adjust horizontal position
 +
|0-7
 +
|4
 +
|-
 +
|BLACK
 +
|Adjust black level
 +
|0-62
 +
|0
 +
|-
 +
|GAMMA
 +
|Adjust gamma
 +
|OFF / 1 / 2 / 3 / 4
 +
|OFF
 +
|-
 +
|USE_CH
 +
|Selection of usable terminal(s)
 +
|S+VIDEO / S VIDEO
 +
|S+VIDEO
 +
|-
 +
|LANGUAGE
 +
|Language
 +
|JPN / ENG
 +
|JPN
 +
|-
 +
|CRT SYNC
 +
|Sync Polarity
 +
|NEG / POSI
 +
|NEG
 +
|-
 +
|V_SYNC
 +
|Vertical sync rate
 +
|AUTO / 50HZ / 60HZ
 +
|AUTO
 +
|-
 +
|15/31 SCAN
 +
|Resolution
 +
|15KHZ/31KHZ
 +
|31KHZ
 +
|-
 +
|IIC USE
 +
|<font color="#FFA500">*insert explanation*</font>
 +
|OFF / ON
 +
|ON
 +
|-
 +
|AFC
 +
|Upper screen distortion correction
 +
|0-8
 +
|0
 +
|-
 +
|AFC SAVE
 +
|Saving AFC setting when shutting off
 +
|OFF / ON
 +
|OFF
 +
|-
 +
|AFC BOW
 +
|<font color="#FFA500">*insert explanation*</font>
 +
|
 +
|Middle
 +
|-
 +
|AFC ANGLE
 +
|<font color="#FFA500">*insert explanation*</font>
 +
|
 +
|Middle
 +
|-
 +
|AFC DEF
 +
|<font color="#FFA500">*insert explanation*</font>
 +
|
 +
|0
 +
|-
 +
|RESET LOCK
 +
|<font color="#FFA500">*insert explanation*</font>
 +
|OFF / LOCK1 / LOCK2
 +
|LOCK1
 +
|-
 +
|SUPER MODE
 +
|Super Mode
 +
|OFF / ON
 +
|OFF
 +
|-
 +
|D/A LEVEL
 +
|<font color="#FFA500">*insert explanation*</font>
 +
|
 +
|
 +
|-
 +
|A/D LEVEL
 +
|<font color="#FFA500">*insert explanation*</font>
 +
|
 +
|
 +
|-
 +
|DTC_TYP
 +
|Dot clock selection
 +
|NTSC / PS / USER
 +
|NTSC
 +
|-
 +
|USR_DTC
 +
|User dot clock adjustment
 +
|1 - 62
 +
|59
 +
|-
 +
|V_LINE
 +
| Scanlines
 +
|OFF / ON
 +
|OFF
 +
|}
 +
 +
Super Mode is available when starting the unit and waiting for five seconds then press select
 +
<br>
 +
and menu simultaneously and then press up, up, down, down, left, right, left, right, select and menu.
 +
 +
 +
Note! that this is when using the RGB input (GAME IN) using the other inputs has a few unique extra features not shown here.
  
 
== Specifications ==
 
== Specifications ==
Line 105: Line 244:
 
* RGB in 15-pin D-sub (for older Japanese monitors)
 
* RGB in 15-pin D-sub (for older Japanese monitors)
 
* Mini Jack for audio output
 
* Mini Jack for audio output
 +
 +
=== Capacitor List ===
 +
 +
{| class="wikitable" style="text-align:left; width:20%;"
 +
|-
 +
! scope=col | Ver 1.21 PCB
 +
|-
 +
|HOLE:<br>
 +
C158 2200uF/25V<br>
 +
C21 470uF/10V<br>
 +
C134 470uF/10V<br>
 +
C27 470uF/10V<br>
 +
C98 470uF/10V<br>
 +
C45 470uF/10V<br>
 +
C3 470uF/10V<br>
 +
C12 470uF/10V<br>
 +
C30 100uF/16V<br>
 +
C153 100uF/16V<br>
 +
C157 100uF/16V<br>
 +
C73 100uF/16V<br>
 +
C70 100uF/16V<br>
 +
C167 100uF/16V<br>
 +
C118 100uF/16V<br>
 +
C156 47uF/16V<br>
 +
C154 47uF/16V<br>
 +
C63 47uF/16V<br>
 +
C125 47uF/16V<br>
 +
C83 47uF/16V<br>
 +
C155 47uF/16V<br>
 +
C128 47uF/16V<br>
 +
C147 47uF/16V<br>
 +
C13 47uF/16V<br>
 +
C116 47uF/16V<br>
 +
C81 47uF/16V<br>
 +
C132 10uF/50V<br>
 +
C38 10uF/50V<br>
 +
C64 10uF/50V<br>
 +
C57 10uF/50V<br>
 +
C150 10uF/50V<br>
 +
C68 10uF/50V<br>
 +
C67 10uF/50V<br>
 +
C25 10uF/50V<br>
 +
C50 10uF/50V<br>
 +
C99 10uF/50V<br>
 +
C23 10uF/50V<br>
 +
C7 10uF/50V<br>
 +
C24 10uF/50V<br>
 +
C29 10uF/50V<br>
 +
C32 10uF/50V<br>
 +
C82 10uF/50V<br>
 +
C44 22uF/25V<br>
 +
C2 22uF/25V<br>
 +
C8 22uF/25V<br>
 +
C36 10uF/16V<br>
 +
C62 0.47uF/50V<br>
 +
C17 0.47uF/50V<br>
 +
C54 0.47uF/50V<br>
 +
C55 4.7uF/50V<br>
 +
C53 2.2uF/50V<br>
 +
51pcs
 +
|}
 +
 +
[[File:Xrgb2v121caps.jpg]]
 +
 +
=== Manual ===
 +
 +
[http://www.retrosampling.se/Temp/XRGB_MANUALS/Micomsoft%20XRGB-2%20-%20Manual.pdf XRGB-2 Manual (JP)]
 +
 +
[http://www.retrosampling.se/Temp/XRGB_MANUALS/Micomsoft%20XRGB-2%20-%20Manual%20English.pdf XRGB-2 Manual (EN)]
  
 
== FAQ ==
 
== FAQ ==
Line 110: Line 318:
 
=== What is the "RGB/PCB STD" switch for? ===
 
=== What is the "RGB/PCB STD" switch for? ===
  
This little switch physically activate a set of 220 ohm resistors, allowing the use of arcade game [[pcb | pcbs]] on your display device.
+
This little switch physically activates a set of 220 ohm resistors, allowing the use of arcade game [[pcb | pcbs]] on your display device. This is needed since the video level used by PCBs is higher than the one used by game consoles, the resistors make them equivalent.
  
 
=== How to reset XRGB-2 ===
 
=== How to reset XRGB-2 ===
  
 
When the unit is powered down, press all four buttons (up, down, left and right) and then power on the unit. All values will be reset to factory defaults.
 
When the unit is powered down, press all four buttons (up, down, left and right) and then power on the unit. All values will be reset to factory defaults.
 +
 +
=== Important : about GAME IN input (RGB-21) ===
 +
 +
Never directly use the European standard [[SCART]] cables with an XRGB-2 since the pinout is different to the Japanese standard [[RGB-21]] ones, and damage might result due to voltage applied on signal lines.
 +
 +
=== Power Supply ===
 +
 +
Power supplies tend to fail. It requires 12V 0.5 Amp, center positive. Less than 12 and more than 11 tends to give a wobbly image, and less than 10V turns on the LED without output.
  
 
== Scanlines ==
 
== Scanlines ==

Latest revision as of 18:25, 10 August 2018

XRGB-2 Front
XRGB-2 Back
XRGB-2 Box

The XRGB-2 is an upscan converter by Micomsoft. It has limited capabilities when compared to the newer units such as the XRGB-2 plus and the XRGB-3, nevertheless it offers great performance. The stability of the image is rock solid, and you usually don't need to fiddle with settings as much as with later units.

It offers no remote control, and all functions are available through five buttons on the unit's front. It offers just one scanline setting, equivalent to the 127 setting (50%) on the XRGB-3.

Menu

Japanese English Setting Default setting Use
明るさ Brightness 0 - 62 41 Adjust white level
BLUE 0 - 62 31 Adjust blue
GREEN 0 - 62 31 Adjust green
H_POS 0 - 7 4 Adjust horizontal position
BLACK 0 - 62 0 Adjust black level
GAMMA OFF / 1 / 2 / 3 / 4 OFF Adjust gamma
USE_CH S+VIDEO / S VIDEO S+VIDEO
V_SYNC AUTO / 50HZ / 60HZ AUTO
AFC 0 - 8 0
DTC_TYP NTSC / PS / USER NTSC
USR_DTC 1 - 62 59
V_LINE OFF / ON OFF Scanlines

Super Mode menu

Menu Heading Explanation Allowable Range Default
BRIGHTNESS Adjust white level 0 - 62 41
BLUE Adjust blue 0 - 62 31
GREEN Adjust green 0 - 62 31
H_POS Adjust horizontal position 0-7 4
BLACK Adjust black level 0-62 0
GAMMA Adjust gamma OFF / 1 / 2 / 3 / 4 OFF
USE_CH Selection of usable terminal(s) S+VIDEO / S VIDEO S+VIDEO
LANGUAGE Language JPN / ENG JPN
CRT SYNC Sync Polarity NEG / POSI NEG
V_SYNC Vertical sync rate AUTO / 50HZ / 60HZ AUTO
15/31 SCAN Resolution 15KHZ/31KHZ 31KHZ
IIC USE *insert explanation* OFF / ON ON
AFC Upper screen distortion correction 0-8 0
AFC SAVE Saving AFC setting when shutting off OFF / ON OFF
AFC BOW *insert explanation* Middle
AFC ANGLE *insert explanation* Middle
AFC DEF *insert explanation* 0
RESET LOCK *insert explanation* OFF / LOCK1 / LOCK2 LOCK1
SUPER MODE Super Mode OFF / ON OFF
D/A LEVEL *insert explanation*
A/D LEVEL *insert explanation*
DTC_TYP Dot clock selection NTSC / PS / USER NTSC
USR_DTC User dot clock adjustment 1 - 62 59
V_LINE Scanlines OFF / ON OFF

Super Mode is available when starting the unit and waiting for five seconds then press select
and menu simultaneously and then press up, up, down, down, left, right, left, right, select and menu.


Note! that this is when using the RGB input (GAME IN) using the other inputs has a few unique extra features not shown here.

Specifications

Inputs

It also has passthrough for:

  • VGA
  • RCA Audio
  • Mini Jack

Outputs

  • VGA at 640x480 31khz
  • RGB in 15-pin D-sub (for older Japanese monitors)
  • Mini Jack for audio output

Capacitor List

Ver 1.21 PCB
HOLE:

C158 2200uF/25V
C21 470uF/10V
C134 470uF/10V
C27 470uF/10V
C98 470uF/10V
C45 470uF/10V
C3 470uF/10V
C12 470uF/10V
C30 100uF/16V
C153 100uF/16V
C157 100uF/16V
C73 100uF/16V
C70 100uF/16V
C167 100uF/16V
C118 100uF/16V
C156 47uF/16V
C154 47uF/16V
C63 47uF/16V
C125 47uF/16V
C83 47uF/16V
C155 47uF/16V
C128 47uF/16V
C147 47uF/16V
C13 47uF/16V
C116 47uF/16V
C81 47uF/16V
C132 10uF/50V
C38 10uF/50V
C64 10uF/50V
C57 10uF/50V
C150 10uF/50V
C68 10uF/50V
C67 10uF/50V
C25 10uF/50V
C50 10uF/50V
C99 10uF/50V
C23 10uF/50V
C7 10uF/50V
C24 10uF/50V
C29 10uF/50V
C32 10uF/50V
C82 10uF/50V
C44 22uF/25V
C2 22uF/25V
C8 22uF/25V
C36 10uF/16V
C62 0.47uF/50V
C17 0.47uF/50V
C54 0.47uF/50V
C55 4.7uF/50V
C53 2.2uF/50V
51pcs

Xrgb2v121caps.jpg

Manual

XRGB-2 Manual (JP)

XRGB-2 Manual (EN)

FAQ

What is the "RGB/PCB STD" switch for?

This little switch physically activates a set of 220 ohm resistors, allowing the use of arcade game pcbs on your display device. This is needed since the video level used by PCBs is higher than the one used by game consoles, the resistors make them equivalent.

How to reset XRGB-2

When the unit is powered down, press all four buttons (up, down, left and right) and then power on the unit. All values will be reset to factory defaults.

Important : about GAME IN input (RGB-21)

Never directly use the European standard SCART cables with an XRGB-2 since the pinout is different to the Japanese standard RGB-21 ones, and damage might result due to voltage applied on signal lines.

Power Supply

Power supplies tend to fail. It requires 12V 0.5 Amp, center positive. Less than 12 and more than 11 tends to give a wobbly image, and less than 10V turns on the LED without output.

Scanlines

This unit has only one scanline setting, and is activated by turning on the last option in the menu, named V_LINE.

In order to compare the scanlines to those of the XRGB-3, several pictures were taken at different scanline levels. The results matched at level 127 of the XRGB-3. The same cables, arcade PCB, camera settings and TV were used to connect and compare them. The images show a cropped section of pure white on the CRT calibration screen of a System 16 board.

XRGB-2-Scanlines.jpg XRGB-3-Scanlines-127-cropped.jpg
XRGB-2 with scanlines photo XRGB-3 with scanlines at 127
XRGB-3-Scanlines-001-cropped.jpg
XRGB-3 with scanlines at 001 for reference