Xbox

Models

insert data

Models tested

insert data

XRGB-2 Specific settings

insert data

XRGB-3 Specific settings

insert data

XRGB-Mini Specific settings

insert data

OSSC Specific settings

No special settings are required for basic functionality.

The OSSC can however be set up to perform NTSC square pixel sampling. When doing so, the sampling matches the pixel clock in games running at square pixel 640x480 resolution and maintains a correct 4:3 aspect ratio. The latter also applies to games that run at a non-square pixel 720x480 resolution (albeit with a 2% total horizontal crop). This setup is especially useful when using 4x mode with 480i input and 2x mode with 480p input, where the default settings may produce an incorrect aspect ratio.

It can also be used for 2x mode with 480i input and passthru mode with 480p input if desired.

The settings need to be chosen with respect to the video encoder (Conexant, Focus Enhancements, Xcalibur) used in the particular revision of the Xbox, due to differences in their video timings.

Note that compatibility with these settings can vary between displays

NTSC/PAL square pixel settings for revision 1.4 (Focus) models

In Sampling opt. menu

Parameter	Recommended setting	Notes
Allow TVP HPLL2x	Off	This setting is only recommended to be enabled if the picture becomes jittery or unstable, as it can cause sampling phase to randomly shift 180° and blur the picture.
Allow upsample2x	On/Off	This is optional but recommended when using 4x mode with 480i input or 2x mode with 480p input to maintain smooth edges and detail in games that use 720x480 resolution. Most likely required for interlaced signals.

In Adv. timing sub menu

Parameter	Setting			Notes
	in 480i	in 480p	in 576i
H. samplerate	762	762	768
H. s.rate frac	.65	.65	.00	(480) Might need to be adjusted to higher value in order to get a picture.
H. synclen	62	62	63
H. backporch	44	42	55	Might need to be adjusted up or down a step or two to center the picture.
H. active	640	640	640
V. synclen	3	6	3
V. backporch	16	30	19	Might need to be adjusted up or down a step or two to center the picture.
V. active	240	480	288
Sampling phase	236	180	292	Might need to be adjusted if you see crosstalk/noise

In Adv. timing sub menu (Widescreen)

Parameter	Setting			Notes
	in 480i	in 480p	in 576i
H. samplerate	858	858	864
H. s.rate frac	.00	.00	.00
H. synclen	62	62	63
H. backporch	57	55	70	Might need to be adjusted up or down a step or two to center the picture.
H. active	720	720	720
V. synclen	3	6	3
V. backporch	16	30	19	Might need to be adjusted up or down a step or two to center the picture.
V. active	240	480	288
Sampling phase	157	123	135	Might need to be adjusted if you see crosstalk/noise

When playing games in progressive scan with the above settings, disabling the Allow upsample2x option will produce sharper edges between pixels. If that option is desired, it is also necessary to disable Allow TVP HPLL2x and adjust Sampling phase to reduce bleeding between pixels.

Note that disabling Allow upsample2x with the above settings while interlaced might lose signal from monitor/TV (If signal is still lost while this is on then H. s.rate frac needs to be higher or H. samplerate has to be 763.00).

NTSC square pixel settings for revision 1.6 (Xcalibur) models

In Sampling opt. menu

Parameter	Recommended setting	Notes
Allow TVP HPLL2x	Off	This setting is only recommended to be enabled if the picture becomes jittery or unstable, as it can cause sampling phase to randomly shift 180° and blur the picture.
Allow upsample2x	On	This is optional but recommended when using 4x mode with 480i input or 2x mode with 480p input to maintain smooth edges and detail in games that use 720x480 resolution.

In Adv. timing sub menu

Parameter	Setting		Notes
	in 480i	in 480p
H. samplerate	780	780
H. s.rate frac	.00	.00
H. synclen	58	58
H. backporch	60	60	Might need to be adjusted up or down a step or two to center the picture.
H. active	640	640
V. synclen	3	6
V. backporch	16	32	Might need to be adjusted up or down a step or two to center the picture.
V. active	240	480

When playing games that have a resolution of 640x480 with the above settings, disabling the Allow upsample2x option will produce sharper edges between pixels. If that option is desired, it is also necessary to disable Allow TVP HPLL2x and adjust Sampling phase to reduce bleeding between pixels.

Note that disabling Allow upsample2x with the above settings will cause some loss in clarity with games that run at 720x480.